 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DATA SHEET BIPOLAR ANALOG INTEGRATED CIRCUIT PC3533,3504 THREE-THERMAL POSITIVE OUTPUT VOLTAGE DESCRIPTION The PC3533 and 3504 are three-thermal positive output voltage regulators with an output current of 1 A at respective output voltages of 3.3 and 4 V. These regulators are guaranteed to operate at as low as -40C. FEATURES * Output current capacity: 1 A * On-chip overcurrent limiter * On-chip output transistor safe operation area protection * On-chip thermal protection * Output capacitor capacitance: 0.1 F or higher * Wide operating temperature range: TA = -40 to +85C PIN CONFIGURATION (Marking Side) PC3533HF, 3504HF: MP-45G Constant current source BLOCK DIAGRAM INPUT Startup circuit Reference voltage circuit Safe operation area protection Error Amp. Overcurrent protection OUTPUT 1: INPUT 2: GND Marking 1 2 3 3: OUTPUT Thermal shut down GND ORDERING INFORMATION Part Number Package MP-45G (Isolated TO-220) MP-45G (Isolated TO-220) Outputs 3.3 V 4.0 V Marking 3533 3504 Packing Type * Bag stuffing * Bag stuffing PC3533HF PC3540HF The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. G15965EJ2V0DS00 (2nd edition) Date Published July 2002 NS CP(K) Printed in Japan The mark 5 shows major revised points. (c) 2002 PC3533, 3504 ABSOLUTE MAXIMUM RATINGS (TA = 25C unless otherwise specified) Parameter Input Voltage Internal Power Dissipation (TC = 25C) Operating Ambient Temperature Operating Junction Temperature Storage Temperature Thermal Resistance (junction to case) Thermal Resistance (junction to ambient) Symbol VIN PT TA TJ Tstg Rth(J-C) Rth(J-A) Rating -0.3 to +25 15 Note -40 to +85 -40 to +150 -55 to +150 7 65 Unit V W C C C C/W C/W Note Internally limited. When the operating junction temperature rises over 150C, the internal circuit shuts down the output voltage. Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. TYPICAL CONNECTION D1 INPUT CIN PC3533, 3504 + OUTPUT COUT D2 CIN: 0.1 to 0.47 F or higher. Set this value according to the length of the line between the regulator and INPUT pin. Be sure to connect CIN to prevent parasitic oscillation. Use of a film capacitor or other capacitor with excellent voltage and temperature characteristics is recommended. If using a laminated ceramic capacitor, it is necessary to ensure that CIN is 0.1 F or higher for the voltage and temperature range to be used. COUT: 0.1 F or higher. Be sure to connect COUT to prevent oscillation and improve excessive load regulation. Place CIN and COUT as close as possible to the IC pins (within 2 cm). Also, use an electrolytic capacitor with low impedance characteristics if considering use at sub-zero temperatures. D1: If the OUTPUT pin has a higher voltage than the INPUT pin, connect a diode. D2: If the OUTPUT pin has a lower voltage than the GND pin, connect a Schottky barrier diode. Caution Make sure that no voltage is applied to the OUTPUT pin from external. 2 Data Sheet G15965EJ2V0DS PC3533, 3504 RECOMMENDED OPERATING CONDITIONS Parameter Input Voltage Symbol VIN Type Number MIN. 5.8 6.5 0.005 TYP. MAX. 20 20 1 Unit V V A PC3533 PC3504 Output Current IO All Caution Use of conditions other than the above-listed recommended operating conditions is not a problem as long as the absolute maximum ratings are not exceeded. However, since the use of such conditions diminishes the margin of safety, careful evaluation is required before such conditions are used. Moreover, using the MAX. value for all the recommended operating conditions is not guaranteed to be safe. Data Sheet G15965EJ2V0DS 3 PC3533, 3504 ELECTRICAL CHARACTERISTICS PC3533 (TJ = 25C, VIN = 5.8 V, IO = 0.5 A, CIN = 0.33 F, COUT = 0.1 F, unless otherwise specified) Parameter Output Voltage Symbol VO1 VO2 Line Regulation REGIN1 REGIN2 Load Regulation REGL1 REGL2 Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage IBIAS 5.8 V VIN 20 V, 5 mA IO 1 A 5.8 V VIN 20 V 5.8 V VIN 9 V 5 mA IO 1 A 250 mA IO 750 mA Conditions MIN. 3.168 3.135 20 10 20 10 2.8 5.8 V VIN 20 V 10 Hz f 100 kHz f = 120 Hz, 5.8 V VIN 9 V IO = 1 A VIN = 5.8 V VIN = 10 V IO = 5 mA, 0C TJ 125C 1.0 55 57 2.0 1.8 2.1 - 0.4 2.8 2.5 TYP. 3.3 MAX. 3.432 3.465 50 30 50 20 6 1.0 Unit V V mV mV mV mV mA mA IBIAS1 Vn R*R VDIF IOshort1 IOpeak Vr.m.s. dB V A A mV/C VO/ T PC3504 (TJ = 25C, VIN = 6.5 V, IO = 0.5 A, CIN = 0.33 F, COUT = 0.1 F, unless otherwise specified) Parameter Output Voltage Symbol VO1 VO2 Line Regulation REGIN1 REGIN2 Load Regulation REGL1 REGL2 Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage IBIAS 6.5 V VIN 20 V, 5 mA IO 1 A 6.5 V VIN 20 V 6.5 V VIN 10 V 5 mA IO 1 A 250 mA IO 750 mA Conditions MIN. 3.84 3.80 20 10 20 10 2.8 6.5 V VIN 20 V 10 Hz f 100 kHz f = 120 Hz, 6.5 V VIN 10 V IO = 1 A VIN = 6.5 V VIN = 10 V IO = 5 mA, 0C TJ 125C 1.1 55 60 2.0 1.8 2.1 - 0.4 2.8 2.5 TYP. 4.0 MAX. 4.16 4.20 50 30 50 20 6 1.0 Unit V V mV mV mV mV mA mA IBIAS1 Vn R*R VDIF IOshort1 IOpeak Vr.m.s. dB V A A mV/C VO/ T 4 Data Sheet G15965EJ2V0DS PC3533, 3504 5 TYPICAL CHARACTERISTICS (Reference Values) PD vs. TA VO vs. VIN ( PC3533) 4.0 IO = 5 mA 20 PD - Total Power Dissipation - W VO - Output Voltage - V 15 3.0 IO = 0.5 A IO = 1.0 A ith W 10 Wit h1 0C /W 2.0 inf ini te i ats he 5 1.92 0 0 25 50 hea tsin k 1.0 nk Without heat sink 85C 0 TJ = 25C 0 1 2 3 4 5 6 7 8 9 10 75 100 125 150 TA - Operating Ambient Temperature - C VO vs. VIN ( PC3504) 5.0 3.0 2.5 2.0 1.5 1.0 0.5 0 VIN - Input Voltage - V IBIAS vs. VIN ( PC3533) 4.0 VO - Output Voltage - V IO = 5 mA IO = 0.5 A IBIAS - Quiescent Current - mA IO = 5 mA IO = 0.5 A IO = 1.0 A 3.0 IO = 1.0 A 2.0 1.0 TJ = 25C 0 1 2 3 4 5 6 7 8 9 10 0 TJ = 25C 0 1 2 3 4 5 6 7 8 9 10 VIN - Input Voltage - V IBIAS vs. VIN ( PC3504) VIN - Input Voltage - V VO vs. TJ 50 IO = 5 mA 3.0 2.5 2.0 1.5 1.0 0.5 0 TJ = 25C 0 1 2 3 4 5 6 7 8 9 10 IO = 5 mA IO = 0.5 A IO = 1.0 A VO - Output Voltage Deviation - mV IBIAS - Quiescent Current - mA 25 PC3533 0 -25 PC3504 -50 -50 0 50 100 150 VIN - Input Voltage - V TJ - Operating Junction Temperature - C Data Sheet G15965EJ2V0DS 5 PC3533, 3504 R R vs. f 100 90 . IOpeak vs. VDIF ( PC3504) 2.5 TJ = 25C R R - Ripple Rejection - dB 80 70 60 50 40 30 20 10 0 PC3533 IOpeak - Peak Output Current - A 2 1.5 PC3504 1 . 0.5 IO = 0.5 A 10 100 1000 f - Frequency - Hz 10000 100000 0 0 5 10 15 20 25 VDIF - Dropout Voltage - V IOpeak vs. VDIF ( PC3533) 2.5 TJ = 25C 80 R R vs. IO TJ = 25C, f = 120 Hz PC3504: 6.5 V VIN 10 V PC3533: 5.8 V VIN 9 V . IOpeak - Peak Output Current - A 2 R R - Ripple Rejection - dB 70 PC3504 60 1.5 PC3533 50 1 . 0.5 40 0 0 5 10 15 20 25 VDIF - Dropout Voltage - V 30 -0.2 0 0.2 0.4 0.6 0.8 1 1.2 IO - Output Current - A VDIF vs. IO 2.5 2.5 VDIF vs. TJ ( PC3533) IO = 1.0 A VDIF - Dropout Voltage - V VDIF - Dropout Voltage - V 2 2 1.5 1.5 IO = 0.1 A IO = 0.5 A 1 1 0.5 TJ = 25C 0 0 0.2 0.4 0.6 0.8 1 1.2 IO - Output Current - A 0.5 0 -50 -25 0 25 50 75 100 125 TJ - Operating Junction Temperature - C 6 Data Sheet G15965EJ2V0DS PC3533, 3504 VDIF vs. TJ ( PC3504) 2.5 IO = 1.0 A VDIF - Dropout Voltage - V 2 IO = 0.5 A 1.5 IO = 0.1 A 1 0.5 0 50 25 0 25 50 75 100 125 TJ - Operating Junction Temperature - C Data Sheet G15965EJ2V0DS 7 PC3533, 3504 PACKAGE DRAWING PC3533HF, 3504HF 3PIN PLASTIC SIP (MP-45G) A E B P N I L D 1 2 3 M K Y H Z C F NOTE J V U G M ITEM A B C D E F G H I J K L M N P U V Y Z MILLIMETERS 10.00.2 7.00.2 1.500.2 17.00.3 3.30.2 0.750.10 0.25 2.54 (T.P.) 5.00.3 2.460.2 5.00.2 8.50.2 8.50.2 4.50.2 2.80.2 2.40.5 0.650.10 8.90.7 1.300.2 P3HF-254B-4 Each lead centerline is located within 0.25 mm of its true position (T.P.) at maximum material condition. ' 8 Data Sheet G15965EJ2V0DS PC3533, 3504 RECOMMENDED MOUNTING CONDITIONS The following conditions must be met for mounting conditions of the PC3533, 3504. For more details, refer to the Semiconductor Device Mounting Technology Manual (C10535E). Please consult with our sales offices in case other mounting process is used, or in case the mounting is done under different conditions. Type of Through-hole Device PC3533HF, 3504HF: MP-45G Process Wave Soldering (only to leads) Partial Heating Method Solder temperature: 260C or below, Flow time: 10 seconds or less Pin temperature: 300C or below, Heat time: 3 seconds or less (Per each pin). Conditions Caution For through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered. Data Sheet G15965EJ2V0DS 9 |
Price & Availability of UPC3540HF
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |